1) Phone: (610) 906-3549
Need Technical Help? [email protected]
2) Fax: (610) 340-9054
Bookmark and Share
4 Ways To Order:
EU/UK Call: +44 (0) 1202 233 268 Fax: +44 (0) 1202 830 425
4) Ecommerce: Use the "E-catalog" link to the right
(Our e-catalog is a work-in-progress... not all items shown on this site or in our catalogs are available in the e-catalog. Completion date expected July 30)
Order Desk Tel: (610) 906-3549 . . . 8am-5:30pm Eastern M-F
Go to content
Applications

Commercial Kitchen Ductwork Gasket Seal Tape - Sealant - Access Doors

Commercial Kitchen Grease Duct Gasket Seal Tape
Commercial Kitchen Grease Duct Gasket Seal Tapes
commercial kitchen duct sealant adhesive

Ductwork Flange Gasket Sealing Tapes


Common tape widths

Most flanges are between 1" and 2" in width, with some extending to 2 1/4 or 2 1/2" wide.  Most flanges utilize a 1/4" stud line to join the flange faces.  Some may be 3/8" studs.

Tapes to interface between the flange faces are available in Plain construction and Bolt-Hole Drop Warp construction (LadderTape).  Using a plain tape, a length of tape is installed along the inside of the bolt hole line, and another length of tape is installed on the outside of the bolt hole line.  In this case the tape is typically less than 1/2 of the width of the flange width - so for example, on a 1 1/2" flange, the tape width may only be 1/2" wide.

Using a Bolt-Hole Drop Warp construction tape (LadderTape), the tape is installed as one piece along the bolt hole line, pressing the center gap of the tape over the studs. In this case the tape is typically similar in width, or the same width, as the flange width.

In the case of plain construction style tapes, to hold the tapes in place while the duct work is handled, the tapes may have PSA on them, or sealant may be used (such as DuctSeal™).

Then the flange is assembled, using Sealant, and the faces are compressed by adding the nuts to the flange bolts.


Material Types and Construction Types

3 material types of tapes are available, and 3 construction types:

  • 1500°F Vermiculite Coated Fiberglass / Plain construction or Bolt-Hole Drop-Warp construction
  • 1800°F Silica / Plain construction or Bolt-Hole Drop-Warp construction or Slit construction
  • 2000°F Ceramic Fiber / Plain construction or Bolt-Hole Drop-Warp construction

Most duristrictions require either a 1500°F rated gasket tape, or a fire exposure rated gasket tape.  DuctSeal tapes cover both ratings.

Tapes are available in a variety of thicknesses - allowing for ductwork surface variances.  For very true metalwork, thin tapes can be used - for ductwork with surface trueness variance a thicker tape with more compression range can be used.

  • 1/32" (0.031") woven tapes
  • 1/32" (0.030") slit tape with adhesive
  • 7/128" (0.054") slit tape with adhesive
  • 1/16" (0.062") woven tapes
  • 11/128" (0.090") slit tapes
  • 1/8" (0.125") woven tapes
  • 23/128" (0.180") slit, folded & stitched tapes
  • 1/4" (0.250") woven tapes

Tape are available with a PSA (pressure sensitive adhesive) added.  Tapes can also be held in place during fitting with our high temperature food contact approved sealant.


Duct Flange Gasket Sealing Adhesive Sealant

Sealant can be used to seal the joints of ductwork to prevent grease migration.

Also used to adhere tapes to metalwork while fitting access doors into place.

Duct Access Doors

Rectangular flat and curved access doors made from Heavy Duty 16 gauge steel.  Stainless steel available.

Also available with extended studs to accommodate fire wrap.  The back frame reinforces the duct cut-out.

Standard and custom sizes available.  The gasket is pre-installed and bonded to the front panel.
AB Technology Group
431 State Street, Box 1491, Ogdensburg, NY 13669
116 Albert Street - Suite 300, Ottawa, ON K1P 5G3
Tel: (610) 906-3549
Fax: (610) 340-9054
Web by Archer-Technology.com
Back to content